.svg)
-
ACCESS POINT MODELS - AP-275 and IAP-275
- 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3×3 MIMO and three integrated omni-directional antennas
- AP-274 and IAP-274
- 2.4-GHz (600 Mbps max) and 5-GHz (1.3 Gbps max) radios, each with 3×3 MIMO and three external antenna connectors
- AP-277 and IAP-277
- 2.4-GHz and 5-GHz radios, each with 3×3 MIMO and three integrated 80° H x 80° V beamwidth directional antennas
WIRELESS RADIO SPECIFICATIONS - AP type: Outdoor, dual radio, 5-GHz 802.11ac and 2.4-GHz 802.11n
- In addition to 802.11n data rates, the 2.4-GHz radio supports 802.11ac data rates using 256-QAM modulation. This gives TurboQAM-enabled clients a 33% boost above the maximum supported data rate to deliver up to 600 Mbps.
- 3×3 MIMO with three spatial streams and up to 1.3 Gbps wireless data rate
- Supported frequency bands (country-specific restrictions apply):
- 2.4000 GHz to 2.4835 GHz
- 5.150 GHz to 5.250 GHz
- 5.250 GHz to 5.350 GHz
- 5.470 GHz to 5.725 GHz
- 5.725 GHz to 5.875 GHz
- Available channels: Dependent upon configured regulatory domain
- Dynamic frequency selection (DFS) optimizes the use of available RF spectrum
- Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
- 802.11n/ac: 3×3 MIMO with up to three spatial streams
- Supported modulation types:
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM (with TurboQAM clients)
- 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- Transmit power: Configurable in increments of 0.5 dBm
- Maximum (aggregate, conducted total) transmit power (limited) by local regulatory requirements):
- 2.4-GHz band: +28 dBm (23 dBm per chain)
- 5-GHz bands: +28 dBm (23 dBm per chain)
- Advanced cellular coexistence (ACC) feature to minimize interference from cellular systems
- Maximum ratio combining (MRC) for improved receiver performance
- Cyclic delay diversity (CDD) for improved downlink RF performance
- Short guard interval for 20-MHz, 40-MHz and 80-MHz channels
- Space-time block coding (STBC) for increased range and improved reception
- Low-density parity check (LDPC) for high-efficiency error correction and increased throughput
- Explicit transmit beam-forming (TxBF) for increased reliability in signal delivery
- Supported data rates (Mbps):
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 450 (MCS0 to MCS23, 1 to 3 spatial streams)
- 802.11ac: 6.5 to 1,300 (MCS0 to MCS9, 1 to 3 spatial streams
- 802.11n high-throughput (HT) support: HT 20/40
- 802.11ac very high throughput (VHT) support: VHT 20/40/80
- 802.11n/ac packet aggregation: A-MPDU, A-MSDU Power
- Maximum power consumption: 23 watts.
- Direct AC source: 100-240 Volt AC
- Power over Ethernet (PoE): 48 Vdc (nominal) 802.3at compliant source
ANTENNAS - AP-274:
- Six N-type female connectors for external antennas.
- AP-275:
- Six integrated omni-directional antennas for 3×3 MIMO with maximum antenna gain of 5 dBi in 2.4 GHz and 5 dBi in 5 GHz. Built-in antennas are optimized for horizontal mounted orientation of AP-275.
- AP-277:
- Six integrated multipolarized directional antennas with 80° H x 80° V beamwidths for 3 x 3 MIMO with maximum antenna gain of 6.5 dBi in 2.4 GHz and 5GHz.
REGULATORY MODEL NUMBERS - AP-274 and IAP-274: APEX0101
- AP-275 and IAP-275: APEX0100
- AP-277 and IAP-277: APEX0102
WARRANTY - Aruba limited lifetime warranty
- AP-275 and IAP-275
-
MOUNTING - Must be ordered separately
- Optional mounting kits:
- AP-270-MNT-V1: Aruba 270 series AP long mount kit for pole/wall mounting. Reduces impact of obstruction by pole or extends away from corner.
- AP-270-MNT-V2: Aruba 270 series AP short mount kit for pole/wall mounting
- AP-270-MNT-H1: Aruba 270 series AP mount kit for hanging from inclined/horizontal structures
- AP-270-MNT-H2: Low profile mount primarily for AP-277
ENVIRONMENTAL - Operating:
- Temperature: -40° C to +65° C (-40° F to +150°F)
- Humidity: 5% to 95% non-condensing
- Storage and transportation
- Temperature: -40° C to +70° C (-40° F to +158°F)
- Maximum operating altitude: 3000m
- Chassis rating: IP66 and IP67
- Wind survivability: Up to 165 mph
- Shock and vibration: ETSI 300-19-2-4 spec T41.E 4M3
OTHER INTERFACES - One PoE+ PD port 10/100/1000BASE-T Ethernet network interfaces (RJ-45)
- Auto-sensing link speed and MDI/MDX
- One port 10/100/1000BASE-T Ethernet network interfaces (RJ-45)
- Auto-sensing link speed and MDI/MDX
- AC power interface, power cords sold separately
- Serial console interface (micro USB)
- Reset button
- Visual indicator (LED):
- Power/system status; automatically disabled after initial operation period
MECHANICAL - AP-274
- Dimensions/weight (excluding mount):
- 23 cm (W) x 24 cm (D) x 19 cm (H) with aesthetic cover
- 9.0” (W) x 9.4” (D) x 7.5” (H)
- 2.7 kg/6 lbs
- 23 cm (W) x 24 cm (D) x 14 cm (H) without aesthetic cover
- 9.0” (W) x 9.4” (D) x 5.5” (H)
- 2.4 kg/5.3 lbs
- Dimensions/weight (excluding mount):
- AP-275
- Dimensions/weight (excluding mount):
- 23 cm (W) x 24 cm (D) x 27 cm (H)
- 9.0” (W) x 9.4” (D) x 10.6” (H)
- 2.4 kg/5.3 lbs
- Dimensions/weight (excluding mount):
- AP-277
- Dimensions/weight (excluding mount):
- 23 cm (W) x 22 cm (D) x 13 cm (H)
- 9.0″ (W) x 8.7″ (D) x 5.1″ (H)
- 2.1 kg/4.6 lbs
- Dimensions/weight (excluding mount):
REGULATORY - FCC/Industry of Canada
- CE Marked
- R&TTE Directive 1999/5/EC
- Low Voltage Directive 2006/95/EC
- EN 300 328
- EN 301 489
- EN 301 893
- UL/IEC/EN 60950
- EN 60601-1-1, EN60601-1-2
- For more country-specific regulatory information and approvals, please see your Aruba representative.
Sold out
Out of stock
Aruba 270 Series
Innovative and aesthetically-designed, our 270-series outdoor APs deliver fast and reliable 802.11ac Wi-Fi performance under any weather conditions.
Bestsellers
Sold out
Sold out
Sold out
Sold out
Sold out
Sold out
Sold out
